GX550 Aftermarket Wheel & Tire Thread

[jagud09]

Here is the side view of my truck with Westcott lift, +35mm offset Method 703s, and 35x12.5x17 Toyo AT3s at the manufacturer's specified 35 psi.

View attachment 4721View attachment 4722View attachment 4723

So with 11.5 tires and 35mm offset, picture my side view with the tire tucked inboard a 1/2 inch (your 11.5 would be 1 inch narrow, thus 1/2 inch per side. It would be a negligible difference.

If you are poked 10mm farther outboard with a +25mm offset, that's a bit less than 1/2 inch, so it should look essentially the same as my setup. You'll be a few mm inboard of mine, all else being equal. Again, negligible.

Prepare to be happy, you'll like the Westcott treatment!

Awesome! Thank you so much for the detailed response!!

 

[Jrox]

Just saw this short on YouTube, it’s exactly what I would do with my GX OT:

 

[rangertrace]

So no lift at all?

 

[killy]

He said he has the wescott 2.5” lift in the first 30 seconds of the video.

 

[Nebula'Nomad]

Any issue with rubbing? I'm also looking at 35x11.5 on 17x8s with a +25mm offset with the Westcott lift. They suggest a +35mm offset but I'm wondering if the skinnier 11.5" tire (that maybe only measures 34.6") will save me with the 25mm offset?

There was a slight rub on the lower bumper trim. The plastic black piece. Trimmed in neatly about an inch and no other issues since. I'm on an 18x9 with a 20 offset. If you stick with a 35 mm offset no trim should be necessary

 

[Hatrix16]

Maybe a dumb question but I can't readily find the answer - is the stock +50 wheel offset the same for all GX trim-level stock wheels?

I believe +50 is same for all trim packages.

 

[Hatrix16]

Here is the side view of my truck with Westcott lift, +35mm offset Method 703s, and 35x12.5x17 Toyo AT3s at the manufacturer's specified 35 psi.

View attachment 4721View attachment 4722View attachment 4723

So with 11.5 tires and 35mm offset, picture my side view with the tire tucked inboard a 1/2 inch (your 11.5 would be 1 inch narrow, thus 1/2 inch per side. It would be a negligible difference.

If you are poked 10mm farther outboard with a +25mm offset, that's a bit less than 1/2 inch, so it should look essentially the same as my setup. You'll be a few mm inboard of mine, all else being equal. Again, negligible.

Prepare to be happy, you'll like the Westcott treatment!

Did you need to install longer wheel studs for proper retention of the aftermarket wheels?

 

[Bluegill]

I don't believe so. Westcott did the installation so I really don't know.

 

[GX550Key]

Did you need to install longer wheel studs for proper retention of the aftermarket wheels?

BryanM68 posted a video on Oct. 25th in this thread and the guy explains near the end about lug nuts.

 

[tph4m]

18x9 +0 TE37XT
285/70/18 Nitto Grapplers
Wescott Collar Kit

The front bumper needed minor trimming and mudflaps removed due to rubbing. I love it!

 

[BryanM68]

A question for those that have increased tire circumference while leaving the factory spare. Being the rear and center differentials are locking, I assume the rear does not have any type of limited slip. Is anyone concerned about running a different tire circumference if and when you have a flat tire? I would assume at the very least the vehicle would throw a couple of codes due to prolonged wheel speed differences.

 

[Snooperstyle]

37's with Fox lift and 17" Methods with +25 offset and NYTOP front bumper and sliders...

Lexus GX550 Overtrail Build by Bink Designs

 

[JPE]

37's with Fox lift and 17" Methods with +25 offset and NYTOP front bumper and sliders...

Lexus GX550 Overtrail Build by Bink Designs

Interesting they don't mention the MagnaFlow in the description but have a picture of it. I wish they had a recording of what it sounds like.

 

[Snooperstyle]

Interesting they don't mention the MagnaFlow in the description but have a picture of it. I wish they had a recording of what it sounds like.

Yeah I noticed that too, and was wondering what they did. If you are putting the spare on a rear carrier, then the stock muffler is low hanging fruit. It looks like they installed a smaller rear MagnaFlow muffler to get better clearance than the stock one, and then also did NYTOP's axle dump exhaust with the main MagnaFlow setup, maybe?? Here is a video of the axle dump setup:

 

[GX550Key]

A question for those that have increased tire circumference while leaving the factory spare. Being the rear and center differentials are locking, I assume the rear does not have any type of limited slip. Is anyone concerned about running a different tire circumference if and when you have a flat tire? I would assume at the very least the vehicle would throw a couple of codes due to prolonged wheel speed differences.

Still on the wait list, but this should bring covered in the owner manual. When I upgraded from stock tires to larger KO2's on my Grand Cherokee we took that into consideration. The larger spare fit but the fancy storage trays no longer did.

 

[Robkelhare]

Fuel Charger's 22x9.5/-18. - MT Baja Boss 285/55R22. Had these on when purchased. Did trim the bumper because of rubbing. Came with the spacer lift also, but going to Icon asap. This size tire won't fit as a spare without trimming/removing the guide bracket for the spare. Haven't done that yet cause unsure even if I did that it wouldn't rub the panhard bar.

 

[jplardoux]

Raceline gauge 18x9 et18 with Cooper Discoverer AT3 XLT size 275/70/18

Fit our premium+ with no modifications. The pictures don’t do it justice.. it looks pretty aggressive parked next to our wildtrak and vs stock overtrail.


View attachment 2604View attachment 2605View attachment 2606View attachment 2607View attachment 2608

Please tell us what the offset was for the rim.

 

[munkeeboi]

Please tell us what the offset was for the rim.

They did...it was +18 (et18)

 

[ggils2324]

I have a new Overtrail+…Will 285/65-18’s fit without a lift and no rubbing???

 

[Snooperstyle]

Does anybody know if the TSB replacement brake parts they are using will have issues with 17” rims?
Am I correct in assuming the calipers are not being replaced? Is there anybody on here who had the front brakes replaced already and also is running 17” rims? I’ve got Method 703’s on order, and my dealer has the brake parts on order.